Skip to main content

Volvo EC210B Excavator Superstructure Removal & Installation Guide

This manual show you guide on how to remove and install superstructure for Volvo EC210B excavators.The superstructure is heavy. Pay attention to safe footing and the area around the crane before proceeding to remove or install the superstructure.

 

Related Contents:

Volvo PTT Diagnostic software free download

Volvo PROSIS 2019 EPC+Service Manual Free Download


Volvo EC210B Excavator Superstructure Removal
Weight of superstructure : 4 ~ 7 tons excluding counterweight and digging unit.
1.1. Remove the digging unit.it.
2.2. Disconnect center passage clamping screw, seal cover, hydraulic oil hoses, drain hose, and one servo hydraulic oil hose from center passage.
NOTE!
Bundle the hoses. Blind plug each disconnected hose and pipe.

3. Remove screws (A) fixing the outer race of the slew ring.ng.
4.4. Dismantle the cab, counterweight and guard. Place a wire rope on the superstructure and lift it with a crane to anan extent that the wire rope is not slack.
5.5. Lift the superstructure just a little, and after confirming safety all around, lift it up and out.

Volvo EC210B Excavator Superstructure Installation
1.1. Bundle the hoses attached to the center passage together and place them upright.ht.
2.2. Coat the screws and threaded holes of the slew ring with "Threebond kk 1215" (Loctite #515)
3
3. Lift the superstructure and install it to the slew ring.
NOTE!
Lower the superstructure so that the slew pinion and the slew ring are engaged.
NOTE!
For tightening torque, see torque chart.
NOTE!
Tighten diagonally opposite screws in sequence.
4.4. Connect the hoses, center passage clamping screw and seal cover disconnected for removal.




https://www.autoepccatalog.com/product/volvo-ptt-devtool-acpi-plus-installation-activation-service/ 

Labels:

Comments

Post a Comment

Popular posts from this blog

Volvo Truck MID 130 Transmission Control Unit Guide

Volvo Truck MID 130 Transmission Control Unit System Overview The I-Shift transmission is a technologically advanced automated mechanical transmission,designed specifically to work in conjunction with Volvo’s new family of heavy-duty diesel engines. In order to work as a total package, the I-Shift is programmed with each engines efficiency map and is offered with different software options to fulfill each operators needs.
Post a Comment
Read more

Volvo EC330B Excavator Engine Start and Stop Circuit Old Overview

Volvo EC330B Excavator Engine Start and Stop Circuit Old Overview  Volvo PTT Procedures: Engine Start and Stop Circuit(Old) Power from battery => electric greasing system,start key,start motor,battery relay Power from battery relay =>safety start relay Vocom 88890300 1) Key ON  BR=> Battery relay,alternator(15,pre-magnetization)  ACC=>VECU,Air conditioner,EMS power relay 2) Key Start  R2=> VECU  C=> safety start relay 3) Engine running  Alternator(L)=>hour meter,safety start relay,VECU(charge lamp off)  * Resistor between alternator and BR termainal for quick charge lamp off  Alternator(B+)=>alternator(BS,voltage sensing for regulation)  Alternator(15)=>battery relay 4) Key Off  VECU(JA61)=>battery relay
Post a Comment
Read more

Volvo EC330B Excavator Electronic Control System Overview

Volvo ECB330B Excavator Electronic control system overview   Volvo ECB330B Electronic control system is composed of various computers and its communication line. In our system, 2 computer (EECU, VECU) is programmable and 1 computer (MDU) is not. Volvo Tech Tool Communication is important thing to control the machine properly. We use two communication lines that is international protocol. The line is twisted to protect the bus from electrical interference.
Post a Comment
Read more